Ifm-electronic JN2301 Manuel d'utilisateur

Device manualInclination sensor 2 axesJN230180228166/00 04/2015UK

Inclination sensor JN107.5 Configuration examplesFor the examples:Address JN2301 (ECU): 0x19, priority: 1TxPGN0 default group extension (GS): 0x00X:

UKInclination sensor JN11Index Type Value Unit R/W Reset0x1002 UNSIGNED16 TxPGN0 cycle time default: 15 msmin� 15 ms, max� 50000 msms R/W X0x

Inclination sensor JN12Index Type Value Unit R/W Reset0x2042 UNSIGNED8 Index for teach values of the X/Y/Z axes0: no change 1: set teach, relative mea

UKInclination sensor JN138.2.2 Upload/download (0x3000)0x3000 ASCII Programming key R/W8.2.3 Measured data (0xA000 – 0xA011)0xA000 INTEGER16 Longitu

Inclination sensor JN149.2 Euler angle (0x2044 = 1)In this setting the two provided angle values are to be interpreted as Euler angle� The current se

UKInclination sensor JN15be detected by the inclination sensor� In this condition the "inclination value lateral" is insignificant� In pract

Inclination sensor JN1610 Other sensor functions10.1 Device address (0x2000) and baud rate (0x2001)In the case of a change the device address and ba

UKInclination sensor JN17to the direction of gravitation at the teach moment� The Xb direction of the reference system results from the projection of

Inclination sensor JN1810.6 Quadrant correction (0x2040)Quadrant correction means for JN2301 only an extension of the lateral Euler angle to the meas

UKInclination sensor JN19Parameter Index Sub-indexNode ID 0x2000 0x00Baud rate 0x2001 0x00Quadrant correction 0x2040 0x00Heating 0x2041 0x00Teach ind

Inclination sensor JN2Contents1 Preliminary note � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Inclination sensor JN2014 Factory settingIndex Type Value Delivery0x1000 u8 TxPGN0 active 1: is sent cyclically0x2000 u8 Device address 250x2001 u16

UKInclination sensor JN21

UKInclination sensor JN310�6 Quadrant correction (0x2040) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1810�7 Heating (0x2041h)

Inclination sensor JN41 Preliminary noteThis document applies to the device of type "inclination sensor" (art� no�: JN2301)� It is part of

UKInclination sensor JN5The connection terminals may only be supplied with the signals indicated in the technical data and/or on the device label and

Inclination sensor JN65 Scale drawing364,590752245605,36 Electrical connectionThe inclination sensors are fitted with two round 5-pole M12 connector

UKInclination sensor JN77 7 SAE J1939 interfaceThe inclination sensors have a standardised SAEJ1939 interface� All measured values and parameter gro

Inclination sensor JN87.2 Proprietary PDU format 1 protocolThe parameters of the JN2301 sensors are listed in a table that is accessed per 16-bit ind

UKInclination sensor JN97.3 Configuration examplesAddress target unit (ECU): 0x19Address control unit / master: 0x14Priority of the message: 3Example